![]() If the matrix is still out of range, set the DCLK as low as possible and adjust the refresh rate until you are able to get the panel in range.That should make your matrix come in range if it was out. Check your cabinet setting, if anything is in red, adjust the multiple down from refresh x16 to refresh x8. On the main screen, the module size at the top should now read 64x16.After that, click the first square on line 10, then 11, 12, 13, 14, 15, and 16. ![]() Start on line nine column one and drag your cursor across until the end. On the final page, you should have a screen that is 64 cells wide by 16 cells tall.On Guide 6, set the number to two, press next.On Guide 5, set the number to 16, press next.When you get to guide 4, switch the colors, if needed, and press next.Fill in the width as 64, press next, and next your way to guide 4 (in the title bar).Click "Intelligent Setting" at the bottom.If your width and height on the main screen were out of range before, set it properly now even if it is out of range.Click on "Modify" to make the width and height 64x32, click the X next to the sideways pin above.If it is out of range, fudge the numbers so they are in range, we will fix it later. Set your width and height in the two white boxes to your matrix size in pixels.Set the "Data Group" to "Normal 32 Groups".On the center tab (Receiver Parameters), click Load > Preset Parameters > General Parameters Full Color > 14 full color eight scan.Press "Save to Devices" at the bottom of the screen.Make sure the grey box updates with those numbers. The col and row boxes should both be set to 1. On the third tab (Receiver Mapping), click on the box in the grey area and set the width and height of your matrix in pixels.If you get something in the window below, great, if not, you need to troubleshoot this before moving on.Select your network card and press "Detect Receiver Cards.".On the first tab (Sending Device), make sure the middle option labeled "Net Card" is selected.Click Control > LED Screen Settings (password 168).This setting has no major purpose for setup. LED Video Panel P5mm OUTDOOR Pixel Pitch: 5mm LED Configuration: 3-in-1 SMD2121 LED Pixel Density: 192 x 192 per panel Size: 37.8 x 37.8 x 3.5 / 960 x. The x and y parameters correspond to the the location of the virtual display on your computer screen. Click Control > Screen Size and Count Settings.Navigate to the Input / Output Setup Tab and click on Channel Outputs. Now there is a couple of oddities I have found with different setups mainly to do with the orientation of the p5 matrix arrows in the led panels tab. Download and install LEDvision 8.5 or higher, not 5.0 and not 6.8 or 6.9. Now that we have the p5 Panel and pi ready to go we can setup these panels in Falcon Pi Player.Plug your Colorlight card directly into your Gigabit NIC without anything in between such as a switch.Refer to the P5 LED screen projects we built.This is a step by step guide that will show you how to configure a Colorlight card to control a set of Wired Watts Outdoor P5 panels. Because operating in an outdoor environment with high temperature can affect the durability of the LED screen. Connect a variety of devices that support images. Save energy up to 40% compared to other types of advertising such as: Leon Large format tarpaulin. The screen is easy to dismantle and repair when there is a problem. P5 LED display has a reasonable installation cost suitable for many customers. Outdoor P5 LED display is also used to display information at squares, railway stations, bus stations, schools, etc. Outdoor P5 LED screen is installed in entertainment areas, music concerts, outdoor events. Outdoor P5 LED screen is used to display brand and product advertising for large and small businesses. Accurate quotation of installation cost of LED screen.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |